Difference between revisions of "Content Dev:CTA Submission Checklist"
Chuck (RL) (Talk | contribs) m (→Shape Relations) |
Chuck (RL) (Talk | contribs) m (→Mouth) |
||
| Line 235: | Line 235: | ||
=== Mouth === | === Mouth === | ||
| − | + | Make sure to check the following conditions are met: | |
| + | *The number of mouth shapes should total 15. | ||
| + | *The mouth shape and its corresponding sound should be compatible. | ||
| + | *Make sure the image names are correct according to guidelines. | ||
| + | *Pay special attention to the phoneme sounds: '''EE''' and '''U'''. | ||
| + | *Verify the integrity of the visuals (section below). | ||
| + | |||
| + | {{Single_Illustration|CTA_FD_Checklist_Mouth_Shapes.png}} | ||
| + | |||
| + | === Visuals === | ||
== Applying Motion == | == Applying Motion == | ||
Revision as of 01:32, 7 March 2018
- Main article: CTA Asset Creation.
Size Comparison
Scale Problems
Make sure that the size of the characters are within the normal range. Typically, this means that an adult character is about 2 squares tall. The size of your character can be determined by its role and type but try not to deviate too much from the norm.
Characters can seem like giants if their heights exceed 2 squares.
Scale Adjustments
Steps:
- Enter the Composer and click on Edit Pose.
- Select the character's hip and resize the character accordingly.
Check the Position
After scaling the entire character make sure:
- The bottom of the feet is placed on the red floor line.
- The center of the character is aligned to the blue symmetry line.
Default Positioning
Frontal Positioning in the Composer
Make sure the bottom of the feet are touching the top of the red line. Make sure the character is centered on the blue line.
Side Positioning in the Composer
The bottom of the right foot should be on top of the red line while the entire character should be centered on the blue line.
Repositioning
Steps:
- Choose Transform Part tool
in the composer. - Open Edit Pose.
- Select the hip bone to move the character about.
Skeletal Structure
The basic skeleton structure.
Limitations
The skeleton can stretch and shrink to accommodate the proportions of the character's limbs. This applies to legs, hands, neck, etc... but the bone angles should not be adjusted.
✔ Right: Symmetrical and correctly aligned.
✘ Wrong: The wrist should not be pre-angled.
✘ Wrong: The knees should not be pre-angled.
✘ Wrong: The ankles should not be pre-angled.
✘ Wrong: Undesirable bending are highlighted in red.
✔ Right: Make sure the bones are aligned.
Joint Rotations
The bone joint should be located at the junction between adjoining images of the limbs.
Possible Joint Issues
Be aware of the neck joint.
Be aware of the wrist joints.
Be aware of the ankle joints.
Be aware of the thigh joints.
Joint Rotation Previewing
One can utilize the transform tool inside Photoshop to check for possible joint rotation defects. This can save time later diagnosing the issue.
Take the elbow as an example:
- Select the LArm image.
- Move the pivot of the transform to the pivot point of the elbow.
- Rotate the image to preview the elbow bend.
If there are any visual defects, move the bone pivot and test again. Repeat these steps until the issue is fixed.
Making Adjustments
Besides fixing the bone defects with Photoshop, one can also use the Composer by
selecting Transform Bone 
to move the bone about.
Adjusting the source image position and rotation by using the Transform Sprite 
tool.
The source image along with its bone can be transformed together by using Transform Part 
in conjunction with Edit Pose 
mode.
Body Part Layer Ordering
Basic Body Layers
- Body part layering can be adjusted on a character to character basis.
- Hand at 0° angle should be set to a layer above the Body.
Body parts rotation at 0°
Body parts rotation at 45°
Basic Face Layers
Face part layering can be adjust on a character to character basis.
Face parts rotation at 0°
Face parts rotation at 45°
Miscellaneous Layers
If the female character is wearing a skirt, then adjust the layers by putting the feet layers below the hip.
Miscellaneous parts rotation at 0°
Miscellaneous parts rotation at 45°
Facial Features
Possible Issues
First make sure that CTA is up to date (ver 3.21)
Taking the mouth as an example:
- Select the character and enter the Composer.
- Select the mouth and open the Bone Editor.
- Adjust the sliders to fix visual defects.
Eye Masking
Pay special attention to clean up the edges and areas around the eye mask so as to not leave floating specks. Otherwise, the eye will "leak" pixels around its periphery during puppeteering.
Face Key Editor
While using Face Key Editor 
, pay special attention to the following sliders:
Squint
Smile Close
Blink
Scare Close
Pupil Change
Shape Relations
Make sure that the images for the facial features switched out do not deviate too much from the originals. You can pull on the Face Key Editor sliders to test out the results.
Pupil change.
It is recommended to fix images that deviate too much from what was intended.
Mouth
Make sure to check the following conditions are met:
- The number of mouth shapes should total 15.
- The mouth shape and its corresponding sound should be compatible.
- Make sure the image names are correct according to guidelines.
- Pay special attention to the phoneme sounds: EE and U.
- Verify the integrity of the visuals (section below).
Visuals
Applying Motion
Use the test files mentioned below to verify the character's compatibility with RL motion:
- BodyTest_F: for front facing characters.
- BodyTest_S: for side facing character.
